Diferencia entre revisiones de «Unimod B1: Assembling»
De WikiRobotics
(→Paso 4: Atornillar el módulo MY1 a la Skycube) |
(→Noticias) |
||
| (No se muestran 5 ediciones intermedias del mismo usuario) | |||
| Línea 35: | Línea 35: | ||
{| {{tablabonita}} | {| {{tablabonita}} | ||
| − | | [[Imagen:Icono_aviso.png]] <font color=red>IMPORTANT!</font> Place the module on top the Skycube board in the same orientation shown in the picture. | + | | [[Imagen:Icono_aviso.png]] <font color=red>IMPORTANT!</font> Place the module on top of the Skycube board in the same orientation shown in the picture. |
|} | |} | ||
| Línea 46: | Línea 46: | ||
|} | |} | ||
| − | === ''' | + | === '''Step 5''': <font color=blue>Connect the servo and the power supply</font> === |
| − | * | + | * Connect the servo to the Skycube board to any of the 3-pin headers available (corresponding to servos number 2, 4, 6 or 8). The black wire should be pointing towards the red power switch. |
| + | |||
{| | {| | ||
| − | || [[Imagen:Unimod-B1-paso5-1.jpg|thumb|300px| | + | || [[Imagen:Unimod-B1-paso5-1.jpg|thumb|300px|Unimod with the servo connected ''(Click to enlarge)'']] |
| − | || [[Imagen:Unimod-B1-paso5-2.jpg|thumb|300px| | + | || [[Imagen:Unimod-B1-paso5-2.jpg|thumb|300px|Unimod, with the power supply connected ''(Click to enlarge)'']] |
|} | |} | ||
| − | === '''Paso 6''': <font color=blue> | + | === '''Paso 6''': <font color=blue>Install the batteries</font> === |
| − | * | + | * Finally, place the 4 AAA batteries in the battery pack. Turn on Unimod to test the power supply connection. The red led should be on. |
{| | {| | ||
| − | || [[Imagen:Unimod-B1-paso6-1-r1.jpg|thumb|300px|Unimod | + | || [[Imagen:Unimod-B1-paso6-1-r1.jpg|thumb|300px|Unimod with the 4 AAA batteries installed ''(Click to enlarge)'']] |
| − | || [[Imagen:Unimod-B1-paso6-2-r1.jpg|thumb|300px|Unimod | + | || [[Imagen:Unimod-B1-paso6-2-r1.jpg|thumb|300px|Unimod is on ''(Click to enlarge)'']] |
|} | |} | ||
| − | == | + | == Pictures == |
{| {{tablabonita}} | {| {{tablabonita}} | ||
| − | | [http://fotos.iearobotics.com/index.php?album=montaje-unimod%2Funimod-b1 | + | | [http://fotos.iearobotics.com/index.php?album=montaje-unimod%2Funimod-b1 Photo album] |
|} | |} | ||
| − | == | + | == Links == |
| + | * [[Training on modular snake robots|Training on modular snake robots (Main page)]] | ||
* [[Unimod]] | * [[Unimod]] | ||
| − | * [[Módulos MY]] | + | * [[Módulos MY|MY1 modules]] |
| − | * [[Skycube| | + | * [[Skycube|Skycube board]] |
| − | == | + | == News == |
| − | * ''' | + | * '''23/Feb/2011''': This page is created |
| − | |||
[[Categoría:Robots modulares]] | [[Categoría:Robots modulares]] | ||
Revisión actual del 07:02 23 feb 2011
Contenido
Introduction
Unimod is the minimal module capable of oscillating autonomously. To assembly it the following parts are needed:
- One MY1 module fully assembled (Assembly instructions)
- One Skycube board
- One flat battery pack for 4 AAA batteries ready to use (Instructions)
- The part D
- 4 male/female spacers. Size M3, length 12mm
- 4 spacers (female/female). size M3, length 10mm
- 8 M3 bolts. Length: 6mm
- 2 M3 falt head bolts. Length: 8mm.
- 2 M3 nuts
Assembling
 IMPORTANT! If one Unimod type A1 has already been mounted and we want to build a new Unimod type B1 from it, just unscrew the MY1 module and rotate it 90 degrees clockwise.
|
Steps 0-3: The same than for the Unimod A1
The step from 0 to 3 are exactly the same than for assembling Unimod type A1:
- Step 0: Remove the paint from the inside of the Part B drill (Optional)
- Step 1: Place the male/female spacers in part D
- Step 2: Screw the_battery pack to the part D
- Step 3: Screw the Skycube board to the part D
Step 4: Screw the MY1 module to the Skycube board
| IMPORTANT! Place the module on top of the Skycube board in the same orientation shown in the picture.
|
Step 5: Connect the servo and the power supply
- Connect the servo to the Skycube board to any of the 3-pin headers available (corresponding to servos number 2, 4, 6 or 8). The black wire should be pointing towards the red power switch.
Paso 6: Install the batteries
- Finally, place the 4 AAA batteries in the battery pack. Turn on Unimod to test the power supply connection. The red led should be on.
Pictures
| Photo album |
Links
News
- 23/Feb/2011: This page is created
