|
|
Línea 125: |
Línea 125: |
| == Links == | | == Links == |
| * [http://www.iearobotics.com/blog/2011/11/09/diseno-e-impresion-de-piezas-3d-con-herramientas-open-source-en-el-master-de-robotica-y-automatizacion-de-la-uc3m/ Entrada en el blog]: 9/Nov/2011 | | * [http://www.iearobotics.com/blog/2011/11/09/diseno-e-impresion-de-piezas-3d-con-herramientas-open-source-en-el-master-de-robotica-y-automatizacion-de-la-uc3m/ Entrada en el blog]: 9/Nov/2011 |
| + | * [http://www.uc3m.es/portal/page/portal/postgrado_mast_doct/masters/robotica_automatizacion/programa/Programa%20201012 Máster de robótica y automatización] en la UC3M |
| | | |
| == Acknowledgements == | | == Acknowledgements == |
Revisión del 13:00 2 may 2012
[[|thumb|400px|(click to enlarge)]]
Ficha del curso
- Título: Diseño e Impresión de Piezas 3D con herramientas Open Source
- Duration:
- Dates:
- Place:
- Organizers:
- Attendees:
- Instructors:
Programme
Day 1
- * About ourselves.
- * Introduction to modular robotics(PDF)
- * Overview of the training on modular snake robots (As shown below)
- Session 2: Building the MY1 modules
- Assembling the MY1 modules. Mounting the battery pack. Preparing the download cable. Building Unimod A1
|
Day 2
- Session 3: Software installation
- Installing the SDCC C compiler. Installing and testing the Codeblocks IDE. Installing and testing the Pydownloader tool. Introduction to the Skycube board. More programming examples
- Session 4: Servo controlling
- Introduction to servo controlling. Programming the sevos. Introduction to the sinusoidal generators. Programming oscillations. Experiment 1: "The wave". Experiment 2: "The big wave"
|
Day 3
- First Challenge! Building a 30 modules caterpillar robot
- Session 5: Locomotion in 1D (I)
- Finish the 10 Unimods A1. Minicube-I assembling. Experiments on the locomotion of Minicube-I. Building the Cube3 configuration. Experiments on the locomotion of Cube3
- Session 6: Locomotion in 1D (II)
- Building the Cube6 configuration. Locomotion experiments. Building the Cube12 configuration. Locomotion experiments. Building the Cube30 configuration! Locomotion experiments. Locomotion principles. Introduction to the serpenoid curve
|
Day 4
- Second challenge! Building a 30-module snake!!
- Session 7: Locomotion in 2D (I)
- Building 10 Unimods B1. Building 10 Unidmods 2D-B1. Building 5 Minicube-II type A1. Building 5 Minicube-II type B1. Locomotion gaits. Locomotions experiments. Building a 6 modules pith-yaw configuration. Locomotion experiments
- Session 8: Locomotion in 2D (II)
- Building 3 snake9. Locomotion experiments. Building 1 snake18. Experiments. Building the snake30!. Locomotion experiments.
|
Day 5
- Session 9: Pending Experiments
- Pending tasks, resolve questions, complete the unfinished experiments
- Session 10: Conclusions and future work
|
Robotic Kit
Unit kit (3 modules) (
click to enlarge)
- 3 Futaba 3003 servos
- Aluminium parts for building 3 MY1 modules
- 1 Aluminium part for holding the batteries
- Battery compartment (for 4 AAA standard batteries)
- 1 Skycube board
- 4 standard AAA batteries
- 43 M3 flat head bolts, 8mm.
- 39 M3 nuts
- 4 male/female spacers. Size M3, length 12mm
- 4 spacers (female/female). size M3, length 10mm
- A two-pin female molex connector
- Two pins for the molex connector
- Two pieces of heat shrink tube. Diameter: 2mm. Length: 10mm
- 3-pin header
- 1 FTDI TTL-232R-5V Cable
- 1 small Label
|
Documentation
Videos
Pictures
Authors
- Alberto Valero Gómez
- Dr. Juan Gonzalez-Gomez. Robotics Lab. Department of system engineering and Automation. Universidad Carlos III de Madrid. Spain
License
Links
Acknowledgements
News
- 02/Mayo/2012: Comenzada esta página