Diferencia entre revisiones de «MY1 modules: assembling»

De WikiRobotics
Saltar a: navegación, buscar
(→‎Step 1: Join the A and B part)
Línea 23: Línea 23:
  
 
=== '''Step 1''': <font color=blue>Join the A and B part</font> ===
 
=== '''Step 1''': <font color=blue>Join the A and B part</font> ===
 +
 +
Parts A and B are joined by means of M3 bolts and nuts. They form the body of the module, where the servo will be screwed.
 +
 +
* '''a)''' Find the A and B pieces. Place the parts as shown in figure a.
 +
* '''b)''' Insert the first bolt with a nut
 +
* '''c)''' Align the drills corresponding to parts A and B. Sometimes it is necessary to force a little bit the part B.
 +
* '''d)''' Insert the bolt and nut.
 +
 +
 
{|
 
{|
 
|| [[Imagen:Montaje-MY1-paso1-1-r2.jpg|thumb|300px| '''a)''' Parts A and B ready to be joined ''(Click to enlarge)'']]
 
|| [[Imagen:Montaje-MY1-paso1-1-r2.jpg|thumb|300px| '''a)''' Parts A and B ready to be joined ''(Click to enlarge)'']]
Línea 31: Línea 40:
 
|}
 
|}
  
−
Las piezas A y B se unen mediante dos tornillos y tuercas. Forman el '''cuerpo''' del módulo, donde irá atornillado el servo.
+
== Pictures ==
−
* '''a)''' Localizar las piezas A y B y orientarlas como se muestra en la figura a.
+
 
−
* '''b)''' Colocar el tornillo y la tuerca del taladro de la pata inferior de la pieza B.
+
{| {{tablabonita}}
−
* '''c)''' Alinear el taladro de la pata superior con el correspondiente de la pieza A. Es necesario forzar un poco la pieza B.
+
| [http://fotos.iearobotics.com/index.php?album=montaje-modulos-my1 Photo album]
−
* '''d)''' Colocar el tornillo con su tuerca.
+
|}

Revisión del 07:16 19 feb 2011

MY1 module assembled (click to enlarge)

Introduction

The MY1 modules consist of three aluminium parts: A, B and C and a Futaba 3003 servo. In addition, five M3 8mm-in-length bolts and nuts are needed.

Beginning: Module parts + servo + bolts + nuts (Click to enlarge)
End: Assembled MY1 module (Click to enlarge)

Assembling

Step 0: Remove the paint inside the drills (Optional)

The module parts are made of 2mm width aluminium. They have been painted in black. The inner part of the drills is also painted therefore its diameter is a little bit smaller. In order for the 3mm bolts to go smooth through the drills it is necessary to remove this paint using a rounded file.

Do it for all the holes in all the parts: A, B and C

Removing the paint of the drills of part B(Click to enlarge)
Removing the paint of the drills of part A(Click to enlarge)

Step 1: Join the A and B part

Parts A and B are joined by means of M3 bolts and nuts. They form the body of the module, where the servo will be screwed.

  • a) Find the A and B pieces. Place the parts as shown in figure a.
  • b) Insert the first bolt with a nut
  • c) Align the drills corresponding to parts A and B. Sometimes it is necessary to force a little bit the part B.
  • d) Insert the bolt and nut.


a) Parts A and B ready to be joined (Click to enlarge)
b) Insert a bolt and a nut(Click to enlarge)
c) Align the drills corresponding to parts B and A (Click to enlarge)
d) Insert the second bolt along with the nut (Click to enlarge)

Pictures

Photo album
Obtenido de «http://iearobotics.com/wiki/index.php?title=MY1_modules:_assembling&oldid=10965»