Diferencia entre revisiones de «Unimod B1: Assembling»

De WikiRobotics
Saltar a: navegación, buscar
(Steps 0-3: The same than for the Unimod A1)
(Steps 0-3: The same than for the Unimod A1)
Línea 27: Línea 27:
 
=== '''Steps 0-3''': <font color=blue>The same than for the Unimod A1</font> ===
 
=== '''Steps 0-3''': <font color=blue>The same than for the Unimod A1</font> ===
 
The step from 0 to 3 are exactly the same than for assembling Unimod type A1:
 
The step from 0 to 3 are exactly the same than for assembling Unimod type A1:
* '''Step 0''': [[Unimod_A1:_Assembling#Step_0:_Remove_the_paint_from_the_inside_of_the_Part_B_drills_.28Optional.29|Step 0: Remove the paint from the inside of the Part B drill]] (Optional)
+
* '''Step 0''': [[Unimod_A1:_Assembling#Step_0:_Remove_the_paint_from_the_inside_of_the_Part_B_drills_.28Optional.29| Remove the paint from the inside of the Part B drill]] (Optional)
* '''Paso 1''': [[Unimod_A1:Montaje#Paso_1:_Colocar_los_separadores_macho-hembra_en_la_pieza_D|Colocar los separadores macho-hembra en la pieza D]]
+
* '''Step 1''': [[Unimod_A1:_Assembling#Step_1:_Place_the_male.2Ffemale_spacers_in_the_part_D|Place the male/female spacers in part D]]
* '''Paso 2''': [[Unimod_A1:Montaje#Paso_2:_Atornillar_el_portapilas_a_la_pieza_D|Atornillar el portapilas a la pieza D]]
+
* '''Step 2''': [[Unimod_A1:Montaje#Paso_2:_Atornillar_el_portapilas_a_la_pieza_D|Atornillar el portapilas a la pieza D]]
* '''Paso 3''': [[Unimod_A1:Montaje#Paso_3:_Atornillar_la_tarjeta_Skycube_a_la_pieza_D|Atornillar la tarjeta Skycube a la pieza D]]
+
* '''Step 3''': [[Unimod_A1:Montaje#Paso_3:_Atornillar_la_tarjeta_Skycube_a_la_pieza_D|Atornillar la tarjeta Skycube a la pieza D]]
  
 
=== '''Paso 4''': <font color=blue>Atornillar el módulo MY1 a la Skycube</font> ===
 
=== '''Paso 4''': <font color=blue>Atornillar el módulo MY1 a la Skycube</font> ===

Revisión del 06:51 23 feb 2011

Unimod type B1 (click to enlarge)

Introduction

Unimod is the minimal module capable of oscillating autonomously. To assembly it the following parts are needed:

  • One MY1 module fully assembled (Assembly instructions)
  • One Skycube board
  • One flat battery pack for 4 AAA batteries ready to use (Instructions)
  • The part D
  • 4 male/female spacers. Size M3, length 12mm
  • 4 spacers (female/female). size M3, length 10mm
  • 8 M3 bolts. Length: 6mm
  • 2 M3 falt head bolts. Length: 8mm.
  • 2 M3 nuts


Beginning: Parts needed to mount one UNIMOD type B1 (Click to enlarge)
End: One Unimod type B1 finished (Click to enlarge)

Assembling

Icono aviso.png IMPORTANT! If one Unimod type A1 has already been mounted and we want to build a new Unimod type B1 from it, just unscrew the MY1 module and rotate it 90 degrees clockwise.

Steps 0-3: The same than for the Unimod A1

The step from 0 to 3 are exactly the same than for assembling Unimod type A1:

Paso 4: Atornillar el módulo MY1 a la Skycube

Icono aviso.png ¡MUY IMPORTANTE! Colocar el módulo encima de la Skycube con la misma orientación mostrada en la foto.
Tarjeta Skycube atornillada a la pieza D y al portapilas, Módulos MY1 y 4 tornillos (Click para ampliar)
Atornillar el Módulo MY1 a la Skycube. ¡Respectar la misma orientación que en la foto! (Click para ampliar)
Módulo atornillado (Click para ampliar)

Paso 5: Conectar el servo y la alimentación

  • Conectar el servo a la Skycube, en cualquier de los conectores rectos, correspondientes a los servos 2, 4, 6 u 8. El cable negro del servo tiene que apuntar hacia el switch rojo de on-off.
Conectar el servo, con la misma orientación mostrada en la foto (Click para ampliar)
Conectar la alimentación (Click para ampliar)

Paso 6: Poner las pilas

  • Por último, colocar las 4 pilas AAA en el portapilas y encender Unimod para comprobar que la conexión se ha hecho correctamente. El led rojo de power on se deberá encender.
Unimod con las 4 pilas AAA colocadas (Click para ampliar)
Unimod encendido (Click para ampliar)

Fotos

Álbum de fotos

Enlaces

Noticias

  • 05/Abril/2010: Primera versión de la página terminada
  • 04/Abril/2010: Comenzada esta página